Sizing, specifying and selecting centrifugal pumps - Gale

Loading...

Sizing, specifying and selecting centrifugal pumps: follow these tips to determine preliminary pump sizing, to support cost-estimation efforts Asif Raza Chemical Engineering. 120.2 (Feb. 2013): p43+. Copyright: COPYRIGHT 2013 Access Intelligence, LLC http://www.accessintel.com/ Full Text: Determining the proper preliminary size for centrifugal pumps during the initial stages of any pump-specification exercise requires numerous calculations and assumptions. This article reviews the steps needed to size centrifugal pumps during the early stages of a project, to support initial cost-estimation efforts. Such early pump-sizing efforts are important steps toward final pump selection and detailed engineering. Sizing centrifugal pumps Normal flowrate and rated flow-rate. To define the normal and rated flowrates, refer to the heat and mass balance of your project. Normal flowrate is the flow at 100% capacity. Rated flowrate is the design margin that is added to the normal flowrate (typically on the order of 10-30%), to accommodate potential short-term excursions in flowrate during operation. Rated flowrate is usually defined by the user. If it is not defined, consider 10% for normal-service pumps, and 20-30% for critical-service pumps, such as distillation column reflux pumps, reactor feed and furnace-feed pumps and other feed pumps that play a critical role in the overall process. Pressure-drop calculations. The intent of these calculations is to determine suction pressure and rated differential pressure. Please refer to sample calculation #1 (discussed below) and Figure 1 for performing pump-sizing calculations, which include calculation of suction pressure and rated differential pressure. Net pressure suction head (NPSH) calculations. During the early stages of the project, the plant layout is not yet firm. Hence, NPSH available for the pump(s) cannot yet be calculated with confidence. However, it is okay to carry out preliminary NPSH calculations using information from the preliminary layout. Note that NPSH values can be increased by later modifications to the layout. NPSH plays a very important role during pump selection, and could significantly impact the cost of the pump if a lowerNPSH (required) pump is specified, since pumps with a lower NPSH requirement tends to be more expensive. The goal is to calculate a preliminary NPSH value and provide it to the pump vendors to get initial feedback. This allows both parties to determine whether a pump with the specified NPSH can be achieved or not, can be achieved with some modification to the plant layout, or can be achieved by selecting a pump with lower NPSH requirements. Based on the vendor's feedback, modify your layout to have a design margin between the available and required NPSH. A design margin of 3-4 ft is widely accepted, per industry standards. See sample calculation #2 for calculating NPSH (available). Horsepower and efficiency. In the early stages of the project, you will have to provide preliminary horsepower to the electrical engineer for load calculations. From the rated differential pressure, calculate the rated horsepower. Since the pump has not yet been selected, you can assume a pump efficiency between 50 and 60%. Make a judgment call--50% is typically a sufficient value for calculating horsepower during the initial stages of a project. Shutoff pressure. Shutoff pressure is required in early stages of the project to determine the flange rating for the discharge piping of the pump. There are several ways to calculate shutoff pressure. A more conservative method uses the following formula: Differential pressure x 1.25 + maximum suction pressure Maximum suction pressure is calculated by: Pressure safety valve (PSV) set pressure x 10-21% accumulation + static head based on high liquid level

If a user does not have information such as the PSV set pressure in the early stages of the project, a simple approach for calculating shutoff head is to use this formula: Rated differential head x 1.5 Specifying centrifugal pumps The following steps must be carried out during the specification of centrifugal pumps: Gather basic process data. Fill out the pump data sheet with the following basic information: Suction pressure, normal and rated discharge pressures, normal flowrate and rated flowrate, fluid properties, such as density, viscosity and vapor pressure at operating temperature. Determine a preliminary value for NPSH. Please refer to the NPSH calculations presented below (sample calculation #2). Specify desired materials of construction. This should come from the end user or from a metallurgist who is involved in the project and is responsible for specifying the appropriate metallurgy of the equipment. Specify sealless versus mechanical seals. Magnetic-drive sealless pumps are desirable for many applications since they eliminate the need for mechanical seals, and thus eliminate the inherent risk of leakage and maintenance associated with such seals. But sealless pumps also have drawbacks, such as an inability to handle larger particles in the process fluids. And in some applications, relatively high differential pressure requires high torque, which may be beyond the capabilities of the sealless pump. Rely on the end-user's experience regarding whether to use a sealed or sealless design pump. Consider seal-less pumps for liquids that are flammable, toxic and corrosive. For instance, many facilities use traditional sealed pumps for pumping water, and sealless pumps for pumping acids and alkalis and other corrosive liquids. Work closely with your vendor and seek guidance based on previous experience in applications with similar service. If a sealless pump is not available, consider using a double mechanical seal to minimize the risk of leakage. Rely on the vendor's experience, as well, in selecting the most appropriate mechanical seal for your service. Provide vendors with as much process data as you have, to ensure proper seal selection for your service. Classify non-ANSI, sub-ANSI and ANSI--API pumps. Ultimately, the selection of specific centrifugal pumps must be based on the end user's requirements, process conditions, and the cost of the equipment. In general, the cost increases in this order: Non-ANSI, sub-ANSI, ANSI and API, while non-ANSI pumps have the lowest cost. A non-ANSI pump usually finds its application in small sizes handling less critical service, such as water that is being pumped at relatively low pressure and low temperature. An ANSI pump is usually used in applications requiring relatively larger sizes (for instance, more than 10 hP) in chemical or hydrocarbon service. However, some ANSI pumps may be limited to a maximum casing pressure. For higher-casing pressures, the user may have no choice but to consider a custom-made pump or an API pump. API pumps tend to be considerably more expensive than ANSI pumps, as they are typically used in hydrocarbon service involving high temperatures and very high pressures. Such pumps are widely used in refinery service.

Specify design pressure and temperature. Specifying design pressure and temperature based on the design conditions of the pump suction vessel may seem to be the easiest approach. But check for any possible upset conditions that might warrant an increase in design pressure and temperature, such as a new process stream entering the pump suction in a different process operating mode. Specify the motor requirements. The required power supply, whether it is 460 V at 60 Hz, or 230 V at 50 Hz, must be supplied by the end user. Lastly you have to specify the hazardous area classifications and temperature rating of the motor. Check with your electrical engineers to identify the required hazardous area classification. Motor temperature rating should also come from the end user. This is based on the lowest autoigni-tion temperature of the components involved in the process. Keep in mind, most of the time, a motor rating up to T3A is available at no added cost, but the cost increases substantially if a motor with a rating of T4 or higher is specified. Next, you need to specify whether you want a fixed-speed motor or a variable-speed drive motor. If you are controlling the pump flow with a speed controller, then you must select an inverted-duty, variable-speed motor. However, note that if there is a control valve on the pump discharge, then you must use a fixed-drive motor. Sample calculations Consider the pump system sketch shown in Figure 1. A fluid with a vapor pressure of 45.9 psia at operating temperature of 430[degrees]F with a viscosity of 0.5 cP is pumped at normal flow of 2,000 gal/min. The specific gravity is 0.7 and the delivery pressure is 100 psig. The operating pressure of column C-100 is 30 psig. The atmospheric pressure at site is 14.5 psia. Assume a rated flowrate of 2,400 gal/min (1.2 times the normal flowrate).

Note that two sets of calculations are done for calculating horsepower--one for normal flowrate and other for rated flowrate. Refer to Figure 1 for calculating static head. Pressure drop across filters, heat exchangers, orifice meters and furnaces are taken from actual equipment vendor quotes. These quotes may be available from different disciplines, such as mechanical and instrumentation departments. If vendor quotes are not available during preliminary pump sizing, then assumptions must be made based on interactions with other disciplines. For instance, it is okay to assume a pressure drop of 10 psid across heat exchangers or a pressure drop of 5-10 psid across a filter. Pressure drop across a vessel filled with catalyst should be calculated using the Ergun equation. These pressure-drop values are finalized when equipment design is finalized and are used for final pump sizing, during the detailed engineering phase, to check the rated differential pressure and rated brake horsepower. It is helpful to perform these calculations using an Excel spreadsheet. The pump-sizing calculations also provide pressure-drop data across the control valve, under normal- and rated-flow circumstances. Specify control-valve pressure drop at the rated flow, following the widely accepted rule of thumb--that is, pressure drop is 25% of the dynamic head loss at rated flow. In this case, dynamic head loss at the rated flow is 151 psig (the sum of pressure drop across filters, heat exchangers, furnaces, orifices and line losses. Hence the differential pressure across the control valve in this scenario at rated flow is 38 psig). Note: If the calculated pressure drop across the control valve is less than 10 psig, use a minimum value of 10 psig for the control valve at rated flowrate. Now adjust the pressure drop across the control valve at normal flow and try to match the discharge pressure until it is equal at normal and rated flow. Pressure drop is directly proportional to the square of the flow, hence pressure drop across rated flow is calculated using the following formula (Note that the rated flow is 1.2 times the normal flow): Filter pressure drop at normal flow = 10 psig Filter pressure drop at rated flow = 10 x (1.2 x 1.2) = 14.4 psig In reality, the discharge pressure at normal flow and rated flow may not be the same, but the two values will be very close. A pump is designed to operate at rated flow conditions. However, a pump operates at normal flow most of the time during normal operation. Normal operation During normal operation, because the flow is lower than the rated flow, the pump will try to develop more head. During this scenario, the control valve will start closing and will consume more pressure drop. This will have the effect of moving the pump back onto the pump curve. Here, you will notice that pressure difference in rated flow is 38 psig (specified by the designer) and is 83.5 psig in normal flow. The difference between these two values is the excess dynamic head between normal flowrate and rated flowrate. The relationship between the pump's head-capacity curve and pipe-system relationship resistance is shown in Figure 4. Pressure drop across the control valve should not be included as a part of the dynamic head loss. The gap between the head-capacity curve and the system-resistance curve is available for throttling (control-valve pressure drop). Control valve pressure drop at normal flow is higher than the pressure drop at rated flow. While pipe dynamic head loss increases at higher flowrates (rated flow), control-valve pressure drop decreases. At higher flowrates, the control valve has to open more and pass larger flow with less resistance. Designers should appreciate the importance of specifying the correct pressure drop for the control valve at different flow conditions, to ensure a rugged system design. If a system is poorly defined, the pump will never be able to control the flow and it will never provide proper flow at the required head. The efficiency will be low and the pump will consume more power.

It is also advisable to install a globe valve at the pump discharge, to allow for throttling the flow and adjusting the flow and discharge pressure. However, please keep in mind that the installation of a globe valve will incur a constant pressure drop, which must be accounted for during head-loss calculations. Ultimately, the calculated control-valve pressure drop at normal and rated flows will be given to the instrument engineer who is responsible for specifying and sizing the control valves for your project. Sample calculation #1. Table 1 shows the results of a pump-sizing exercise, in which suction pressure and rated differential pressure were calculated. TABLE 1 .PUMP-SIZING SPREADSHEET FOR CALCULATING SUCTION PRESSURE AND RATED DIFFERENTIAL PRESSURE (CALCULATION #1) Suction pressure Rated flow Normal flow condition condition Source pressure, psig 30 30 Static head = 10.5 ft (ft x 3.2 3.2 specific gravity/2.31), psi Suction line loss, psi 0.3 0.3 Pump suction pressure, psig (30+3.2) -0.3 = (30+3.2) -0.3 = 32.9 32.9 Discharge pressure Delivery pressure, psig 100 100 Static head = 19 ft (ft x 5.8 5.3 specific gravity/2.31), psi Line loss, psig 33 23 Control-valve pressure drop, 38 83.5 psid Filter pressure drop, psid 14.4 10 Heat exchanger 1 pressure 14.4 10 drop, psid Heat exchanger 2 pressure 14.4 10 drop, psid Furnace pressure drop, psid 72 50 Orifice flowmeter pressure 2.88 2 drop, psid Contingency, psig 10 10 Differential pressure, psig Discharge pressure, psig =100+5.8+3 =100+5.8+2 3+14.4+14. 3+10+10+10 4+14.4+72+ +50+2+83.5 2.88+38+10 +10=305 =305 Minus suction pressure, psig 32.9 32.9 Total pump differential 272 272 pressure, psig Pump head (psi x 2.31 900 900 /specific gravity) Hydraulic power = gal/min x 382 318 pump head (ft) x specific gravity/3,960, hP Efficiency at 3,600 rpm. % 60 60 Rated power = Hydraulic 637 530 power/efficiency, hp Sample calculation #2. Static pressure available at the pump suction inlet = (Operating pressure of the vessel + static head)--suction-piping head loss at rated flow. NPSH (available) = Static pressure at the pump suction inlet--vapor pressure at the operating temperature. The results of these sample calculations are shown in Table 2. TABLE 2.NPSH CALCULATIONS (CALCULATION #2) Atmospheric pressure, psia 14.5 Specific gravity (SG), 0.7 dimensionless Original pressure (vessel 30 pressure), psig Static head = 10.5 ft (Note (10.5/2.31) x 0.7 = 3.18 1) psig Suction line loss, psig 0.3 Suction pressure at pump =30 + 3.18 - (0.3) = 32.88 + inlet flange, psia 14.5 = 47.38 psia Vapor pressure, psia 45.9 Net pressure suction head 47.38-45.9= 1.48 psia (NPSH) = Suc-tion pressure vapor pressure, psia NPSH available, ft = 1.48x2.31/0.7= 4.89 Note 1: Static head in menmired from the low liquid level in the vessel to the center line of the pump-suction flange, or from the vessel bottom nozzle to the center line of the pump-suction flange. The latter is more conservative approach. Pump selection During this stage of the project, you should be getting quotes back from the vendor, based on the pump specifications you have provided. While various quotes will vary in their dollar value, keep in mind that a more-expensive pump does not necessarily mean that it is the best pump for the job, and the least-expensive pump is not worth further consideration. To assess competing quotes fairly, develop a spreadsheet to gather the following selection criteria. Assign points to each item that meets your specifications. NPSH. Check for NPSH (required) from the pump data sheet provided by the vendor. How close it is to your estimated value of NPSH (available)? Ask yourself--Can you make this pump work by increasing NPSH (available)? It cannot be stressed enough that NPSH is a key parameter during pump selection, and insufficient NPSH often results in pump cavitation. Cavitation occurs when vapor bubbles that have formed in areas of low static pressure move along the impeller vanes into high-pressure areas, where they rapidly collapse. The forces produced by these bubbles as they implode erode the impeller vane, resulting in progressive pitting to the impellers. As a rule of thumb, an acceptable margin between NPSH (available) and NPSH (required) is required to ensure pump reliability. A minimum margin of 3-4 ft is a widely practiced rule of thumb. Since the NPSH requirement increases with increasing flow, it is important to consider the maximum expected flow when specifying an acceptable NPSH margin. Rated flow and differential pressure. Analyze all quotes to see whether they meet your specified value of rated flow and differential pressure. Material of construction. Does this meet your specified material of construction? Analyzing pump curve and efficiency. Pump efficiency is a very important value to be considered. Some vendors may quote a bigger pump than what is required. In such a case, the pump efficiency will be reduced. Designers should note that a pump with even 10% higher efficiency will save thousands of dollars in power costs over the service life of the pump.

It is good practice to examine several performance charts at different speeds to see if one model satisfies the requirements more efficiently than another. Whenever possible, the lowest pump speed should be selected, as this will save wear and tear on the rotating parts. Efficiency can be found on the pump curve provided by the pump vendor. Refer to Figure 3, which shows the relationship between efficiency and flowrate. This figure also shows the relationship between volumetric flowrate, head, NPSH and brake horsepower. Every pump has a best efficiency point (BEP), which is the flow/head combination that corresponds to the highest efficiency. The preferred operating region is between 70 and 120% of the BEP flowrate value (1), although most users require the rated flow to fall between 80% and 110% of BEP. The allowable operating region varies from pump to pump, and is defined as the flow range within which vibrations do not exceed the limits established by the American Petroleum Institute (API) (1). Refer to Figure 2, for the recommended operating range. The shaded region represents the operating range, that is discussed in the above paragraph. Note in this figure, there are three curves for three different impeller sizes provided by the pump vendor. While selecting an impeller, it is good practice to select a pump with an impeller that can be increased in size, as this will allow for future increases in head and capacity. Mechanical seal arrangements. When evaluating competing vendor quotes, be sure you are comparing "apples to apples." For instance, some vendors may have quoted a double mechanical seal, while your requirement was for a single seal. If this happens, ask the vendor to revise the quote. Motors. Check for the motor sizing, and whether it has been sized for full run-out case. Full run-out means that the motor should be sized for the maximum fiowrate the pump can deliver. The stated motor temperature rating and specified electrical area classification must meet your requirements. Physical size of the pump. Check for the dimension of the pump from the quotes received. If space is tight, you may have to consider an inline pump, or a high-speed, single-stage pump over a multistage pump. Design conditions. Check for design temperature and pressure from the vendor quotes and make sure that they meet your requirements. Design codes. Does the quoted pump meet your specified design codes, such as API, ANSI and so on. Warranty. When evaluating competing pump options, check for the manufacturer's performance warranties and for the availability of onsite startup assistance from the vendor, if specified in the Request for Quotation (RFQ). Scope of supply for auxiliary equipment. Make sure the vendor's quote includes the supply of all the accessories required, such as lubrication-oil coolers, interconnecting piping between the coolers, instruments, such as flow switches on the cooling water lines and so on. Be sure to compare all the quotes on the same basis. Price. Before selecting a particular pump, make sure that you are comparing "apples to apples," as different vendors may have quoted different pump options in different styles, with different seal arrangements, using different assumptions and so on.

Final thoughts Close coordination with the pump vendor and developing a solid understanding of the process requirements are essential steps during pump design and selection. By understanding the concepts of rated flow, head, suction pressure and NPSH, and by understanding pump curves, you will be on the right track to design and select the most appropriate pump that meets all of the process requirements. Reference (1.) American Petroleum Inst. (API), "Centrifugal Pumps for Petroleum, Petrochemicals and Natural Gas Industries." 10th Ed., API Standards 610 (ISO 13709), Washington, D.C. Asif Raza

Zeton Inc. Author Asif Raza is a lead process engineer at Zeton Inc. (740 Oval Court, Burlington, ON L7L 6A9, Canada; Phone: 905-632-3123; Email: [email protected]). His work involves the design and manufacture of pilot and demonstration units for research and development, in the areas of petroleum refining, petrochemicals, gasification and unconventional sources of energy, such as biomass, gas-to-liquids and coal-to-liquids. He has more than 15 years of experience in process design. His areas of interest include major equipment sizing and selection. P&ID development, selection of control logics and process simulation. Before joining Zeton, Reza worked as a lead design engineer with engineering, procurement and construction (EPC) companies, including Bantrel Inc. and SNC Lavalin Engineers and Constructors. He holds a B.Tech degree in chemical engineering from Amravati University (India). Raza is a registered professional engineer in the province of Ontario, and is a member of Ontario Society of Professional Engineers. Edited by Suzanne Shelley Source Citation (MLA 8th Edition) Raza, Asif. "Sizing, specifying and selecting centrifugal pumps: follow these tips to determine preliminary pump sizing, to support cost-estimation efforts." Chemical Engineering, Feb. 2013, p. 43+. Academic OneFile, http://link.galegroup.com/apps/doc/A319150608/AONE?u=googlescholar&sid=AONE&xid=a25d1ca8. Accessed 28 May 2018. Gale Document Number: GALE|A319150608

Loading...

Sizing, specifying and selecting centrifugal pumps - Gale

Sizing, specifying and selecting centrifugal pumps: follow these tips to determine preliminary pump sizing, to support cost-estimation efforts Asif Ra...

827KB Sizes 2 Downloads 0 Views

Recommend Documents

Sizing, selecting pumps and circulators - | Consulting-Specifying
Oct 15, 2014 - Calculating pressure losses through a piping system for the required head of a pump selection can be done

Selecting Centrifugal Pumps
Developed Head and Developed Pressure of the Pump ............. 0 . . Efficiency and Input ..... Calculation Examples. (

Centrifugal pumps
The total energy of the fluid remains unchanged if there is no inlet or outlet power. When fluid is in motion, the part

Sizing and Selecting Metering Pumps Planning a - PSG Dover
The mini- mum capacity should never be less than 10% of the pump capacity to maintain accuracy. Consider materials of co

Centrifugal Pumps
There are also several pumps combining both principles placed somewhere in between the two extremes in the centrifugal p

Vertical multi-stage centrifugal pumps - DP-Pumps
Operation. The rotating impeller causes the pressure at the inlet of the impeller to drop. This decrease in pressure cre

Sizing conductors and selecting protection devices - Legrand
rules that are used for sizing conductors, wiring systems and their electrical protection ... The complete process for e

Centrifugal water pumps pdf
... deterges the formula frying and centrifugal water pumps pdf tactical training schools in florida phosphorised theore

CENTRIFUGAL PUMP SELECTION, SIZING, AND INTERPRETATION
PUMP SELECTION, SIZING AND INTERPRETATION OF PERFORMANCE. 4 • 3. Performance Curve. At some point in the pump selectio

Centrifugal Pumps - Rimbach Publishing Inc
Oct 17, 2007 - 317/293-2930. 6500. Environmental Treatment Systems. 15-30. 2 1/2/250. •. •. 770/384-0602. Fairbanks